手動閥門，是通過手柄、手輪操作的閥門，是設備管道上使用普遍的一種閥門。它的手柄、手輪旋轉方向順時針為關閉，逆時針為開啟。但也有個別閥門開啟與上述開啟相反。因此，操作前應注意檢查啟閉標志后再操作。

Manual valves are valves operated by handles and handwheels, and are commonly used in equipment pipelines. Its handle and handwheel rotate clockwise to close and counterclockwise to open. But there are also a few valves that open in the opposite direction to the above opening. Therefore, attention should be paid to checking the opening and closing signs before operation.

閥門上的手輪、手柄是按正常人力設計的，因此，在閥門使用上規定，不允許操作者借助杠桿和長扳手開啟或關閉閥門。手輪、手柄的直徑(長度)<320mm的，只允許個人操作，直徑>320mm的手輪，允許兩人共同操作，或者允許一人借助適當?shù)母軛U(一般不超過0.5m長)操作閥門。但隔膜閥、夾管閥、非金屬閥門是嚴禁使用杠桿或長扳手操作的，也不允許過猛關閉閥門。

The handwheel and handle on the valve are designed for normal manual labor, therefore, it is stipulated that operators are not allowed to use levers and long wrenches to open or close the valve during use. For handwheels and handles with a diameter (length)<320mm, only individual operation is allowed. For handwheels with a diameter>320mm, two people are allowed to operate together, or one person is allowed to operate the valve with an appropriate lever (generally not exceeding 0.5m in length). However, diaphragm valves, pinch valves, and non-metallic valves are strictly prohibited from being operated with levers or long wrenches, and excessive force is not allowed to close the valve.

閘閥和截止閥之類的閥門，關閉或開啟到頭(即下死點或上死點)要回轉1/4～1/2圈，使螺紋更好密合，有利操作，以免?得過緊，損壞閥件。

Valves such as gate valves and globe valves, when closed or opened to the end (i.e. bottom dead center or top dead center), should be rotated 1/4 to 1/2 turn to make the threads better fit and facilitate operation, in order to avoid problems? Too tight, damaging the valve components.

有的操作人員習慣使用杠桿和長扳手操作，認為關閉力越大越好，其實不然。這樣會造成閥門過早損壞，甚至釀成事故。除撞擊

Some operators are accustomed to using levers and long wrenches to operate, thinking that the greater the closing force, the better. However, this is not the case. This can cause premature damage to the valve and even lead to accidents. Except for impact